The robot will turn the cube to each face and the camera will take 6 pictures, one of each side of the Cube.  The Raspberry Pi will determine the cube configuration from the six pictures. The Cube configuration will be passed to the kociemba Python library to find an efficient solution. Finally, the robot will execute the moves to solve the Rubik’s Cube!

An important thing to note is that this task is not a light one. It may require several hours of attempts. If you'd rather just solve the cube in your hand and forget about it rather than being able to solve any cube you're given, there are plenty of solvers available on the web. However, the satisfaction of holding a completed Rubik's Cube in your hand and thinking “I did that, and I can do it again” is greater than most, mainly due to the fact that the puzzle has been present in all our lives at some point. By the mid 1980's, an estimated fifth of the world's population had attempted to solve the cube. If you want to stand out and say that you can defeat the puzzle, time and determination is a large factor.
In the publication, during the very first measure, you’re advised you’ll have to practice and trial by mistake. We believe that this block will be enjoyable for kids and adults who love puzzles and don’t mind the complications supporting a Rubik’s Cube. You should have patience in regards to practicing and building. However, as soon as you’re able to resolve it, you’re likely to be quite proud of yourself and the people around you’re likely to be more amazed since it actually requires a whole lot to resolve those cubes.
Here, we're looking at the colours that aren't solved. There are 21 different cases for the top layer, but we only need a couple of algorithms to solve them all. The first thing we want to find is headlights. Only 2 of the cases don't have any headlights (one of them is if you skip this step, and the cube is already solved). For the one case without headlights, just perform the algorithm below from any angle. This is a better case because when you do the next step, the cube will be solved already.
The individual pieces that make up the Rubik's cube are typically produced from plastic. Plastics are high molecular weight materials that can be produced through various chemical reactions called polymerization. Most of the plastics used in a Rubik's cube are thermoplastics. These compounds are rigid, durable, and can be permanently molded into various shapes. The plastics used in the Rubik's cube are acrylonitrile butadiene styrene (ABS) and nylon. Other plastics that might be used include polypropylene (PP), high impact polystyrene (HIPS), and high density polyethylene (HDPE).
Since the center pieces cannot be moved relatively to each other it's important to solve the edge pieces correctly in relation to each other. For example, when solving the white in our case- the green center piece is to the left of the red center piece, therefore the green-white edge piece should to be solved to the left of the red-white edge piece (see image).  

1 When production is initiated, the plastic pellets are transformed into Rubik's cube parts through injection molding. In this process, the pellets are put into the hopper of an injection molding machine. They are melted when they are passed through a hydraulically controlled screw. As the screw turns, the melted plastic is shuttled through a nozzle and physically forced, or injected, into the mold. Just prior to the arrival of the molten plastic, the two halves of the mold are brought together to create a cavity that has the identical shape of the Rubik's cube part. This could be an edge, a corner, or the center piece. Inside the mold, the plastic is held under pressure for a specific amount of time and then allowed to cool. While cooling, the plastic hardens inside the mold. After enough time passes, the mold halves are opened and the cube pieces are ejected. The mold then closes again and the process begins again. Each time the machine moulds a set of parts is one cycle of the machine. The Rubik's cube cycle time is around 20 seconds. Rubiks Build It Solve It Instructions
Since the center pieces cannot be moved relatively to each other it's important to solve the edge pieces correctly in relation to each other. For example, when solving the white in our case- the green center piece is to the left of the red center piece, therefore the green-white edge piece should to be solved to the left of the red-white edge piece (see image).
Headlights are fairly simple to spot. Looking at the image, we can see on the right hand side that the orange edge has a green corner on either side of it. That is a set of headlights. The left hand side has two different colours on either side, so that is not a set of headlights. It is very important to note that a full bar (a blue edge has a blue corner on either side of it, so all three pieces are blue) is also seen as a set of headlights. This is only seen in one case of the 21 though, so you won't see it often. If you have a set of headlights on each side, ignore this part and read the section titled “The U Permutation”. Rubix Builders
1 When production is initiated, the plastic pellets are transformed into Rubik's cube parts through injection molding. In this process, the pellets are put into the hopper of an injection molding machine. They are melted when they are passed through a hydraulically controlled screw. As the screw turns, the melted plastic is shuttled through a nozzle and physically forced, or injected, into the mold. Just prior to the arrival of the molten plastic, the two halves of the mold are brought together to create a cavity that has the identical shape of the Rubik's cube part. This could be an edge, a corner, or the center piece. Inside the mold, the plastic is held under pressure for a specific amount of time and then allowed to cool. While cooling, the plastic hardens inside the mold. After enough time passes, the mold halves are opened and the cube pieces are ejected. The mold then closes again and the process begins again. Each time the machine moulds a set of parts is one cycle of the machine. The Rubik's cube cycle time is around 20 seconds.
In this step we have four pieces to solve. First choose a color to begin with. I chose white in this guide. For this time, choose the white as well, so the images along the solution will be relevant to your solving process. In addition, it is best to start with the white/yellow colors as they are the easiest colors for quick recognition which is important for speedsolving.
This Rubik’s Build It, Solve It kit is for one player – it is recommended for ages 8 and up. As we said before, it is great for children and adults that don’t mind trying to figure out how the cube works – it’s great for those that enjoy putting puzzles together. This kit right here is going to give an inside look on how the cube works and how it’s put together. Plus, you’ll receive some tips in the instruction manual on how to solve it.
Rubik's cube is a toy puzzle designed by Erno Rubik during the mid-1970s. It is a cube-shaped device made up of smaller cube pieces with six faces having differing colors. The primary method of manufacture involves injection molding of the various component pieces, then subsequent assembly, labeling, and packaging. The cube was extremely popular during the 1980s, and at its peak between 1980 and 1983, 200 million cubes were sold world wide. Today sales continue to be over 500,000 cubes sold world wide each year.

product description Blow your mom's mind when you build and solve the Rubik's Build It Solve It Puzzle. With all of the parts necessary for construction along with easy to follow instructions, you can learn how to solve it from the inside out. Put it together, twist it up and use your new found knowledge to make short work of one of life's most beloved puzzles - Rubik's®.


Here, we're looking at the colours that aren't solved. There are 21 different cases for the top layer, but we only need a couple of algorithms to solve them all. The first thing we want to find is headlights. Only 2 of the cases don't have any headlights (one of them is if you skip this step, and the cube is already solved). For the one case without headlights, just perform the algorithm below from any angle. This is a better case because when you do the next step, the cube will be solved already. Rubix Builders
×