The centre pieces on each face, as you may have noticed from playing around with the cube, can't be moved to another spot, only rotated. So we can use this to our advantage by building around the centres. The best centre to build your first cross around is the white centre, as many guides and resources on the web start with a white face, so if you need to look up some steps and examples elsewhere, your cube will look similar to the one that is being used in other demonstrations.


When you get round to building the Rubik’s Cube, you will find it is not as hard as it appears.  The instructions are quite easy to follow and it will probably take you about fifteen minutes. When you get round to placing the colored tiles, pay attention to where they are supposed to go. Because once you snap them into place. you will not be able to remove them. Having said that. you can still use the Rubik’s Cube. What you will not be able to do is follow the instruction guide and solve the puzzle. Rubiks Build It Solve It
If there are no more edges left on the top layer, then they are probably either inserted in the right place but flipped, or inserted in the wrong place. To get an edge out of somewhere it shouldn't be, just insert one of the yellow edges into that slot. This should get the edge out and on the top layer, ready for you to use the above instructions to insert correctly.
When you eventually get the desired position, there are two slightly different variations of it. For this, we need to look at the front of the cube. The yellow corner facing the front can be  in two positions: Either facing the front, or facing the right. In the first image, it is facing the front. This shows you have Sune. To solve it, just do the above algorithm one more time, and you should have oriented all of the top layer.
If you were around in the 1980’s and did not live under a rock, you had a Rubik’s cube.  It was the 3D combination puzzle that had children and adults mesmerized trying to solve the impossible puzzle.  We would spend hours twisting and turning the cube to figure the solution. The cube was invented by an Hungarian professor of architecture, Erno Rubik, in 1974.  Although it took Erno over one month to solve his very own puzzle, it  became a fad and everyone had one. Consequently, it became the world’s best selling toy ever at that time. Rubiks Build It Solve It Instructions
Simply put the 1x1x3 is a pseudo puzzle, It fills a gap in the collection but its not exactly complicated to solve. The way this puzzle was made was by using two centres and a core of a QiYi Sail. As these parts already spin like a 1x1x3 should all I had to do was make these parts into cubies by adding some apoxie sculpt and sanding them smooth. This puzzle was made in an afternoon and stickered the following morning while I was also building my 'Mefferts bandage cube'. Rubix Building Products
Do you remember those complicated little Rubik’s block that we would sit there trying to figure out for what seems like hours? Did any of you guys/girls ever solve them? Maybe all it takes for us to solve the “cube” would be for us to see what it’s all about. While there are many mesmerizing toys that are about to emerge into our world, today, we would like to take a close look at the Rubik’s Build It, Solve It, because we believe this is the one-way ticket to finally solving the cube! Rubix Building Solutions
Keeping white on top, turn the cube so that a different colour face is toward you. Follow the above instructions again. Repeat with the other two faces until the white cross is complete. This step is quite intuitive; you can do it for sure but it does take a little practice. Just move the white edges to their places not messing up the ones already fixed.  

Even in the book, during the first step, you’re told that you will need to practice and trial by error. Personally, we feel that this cube will be more fun for children and adults that enjoy puzzles and don’t mind the complications behind a Rubik’s Cube. You must have patience when it comes to building and practicing. However, once you are finally able to solve it, you’re going to be pretty proud of yourself and the people around you are going to be impressed because it really takes a lot to solve one of these cubes.


Since the center pieces cannot be moved relatively to each other it's important to solve the edge pieces correctly in relation to each other. For example, when solving the white in our case- the green center piece is to the left of the red center piece, therefore the green-white edge piece should to be solved to the left of the red-white edge piece (see image).
Begin with your cube solved. Once again, you want to start off with your Rubik’s cube in its solved position. Making a fish pattern on your Rubik’s cube is simple. The end result will have swapped two edge pieces so that the remaining ones look like a fish with fins. If you hold the cube diagonally it will look like a fish swimming away from you.[7]
The project uses the Pi to directly solve the Rubik’s cube. The BrickPi3 takes the unsolved Rubik’s cube and the Raspberry Pi takes a picture of each side of the Rubik’s cube with the Raspberry Pi Camera. The Pi creates a text map of the color squares that shows where they are located on the cube. When it has fully mapped the cube, the Pi uses the “kociemba” python library to map out the moves needed to solve the Rubik’s cube. This information is taken by the Pi and BrickPi3 to solve the Rubik’s cube using the LEGO motors. The result: a solved Rubik’s cube. Rubix Building Solutions
2 After the cube parts are ejected from the mold, they are dropped into container bins and hand inspected to ensure that no significantly damaged parts are used. The waste sprue material is set aside to be reused or scrapped. Waste material can be ground up and melted again to make new parts, however reground material can degrade and cause poor quality parts. Rubik's cubes are always made from virgin material and never use reground waste plastic.
You can find assembly instructions for the BrickPi3 here. We will need to assemble the case, attach the BrickPi3, the Raspberry Pi, the Raspberry Pi Camera, add an SD Card, and add batteries.  To make the software easier to setup, Raspbian for Robots comes with most of the software you will need already setup.  You will need at least an 8 GB SD Card, and you will want to expand the disk to fit the full size of the SD Card. Rubix Builders
×