You can find assembly instructions for the BrickPi3 here. We will need to assemble the case, attach the BrickPi3, the Raspberry Pi, the Raspberry Pi Camera, add an SD Card, and add batteries. To make the software easier to setup, Raspbian for Robots comes with most of the software you will need already setup. You will need at least an 8 GB SD Card, and you will want to expand the disk to fit the full size of the SD Card.

When you get round to building the Rubik’s Cube, you will find it is not as hard as it appears. The instructions are quite easy to follow and it will probably take you about fifteen minutes. When you get round to placing the colored tiles, pay attention to where they are supposed to go. Because once you snap them into place. you will not be able to remove them. Having said that. you can still use the Rubik’s Cube. What you will not be able to do is follow the instruction guide and solve the puzzle.

Simply put the 1x1x3 is a pseudo puzzle, It fills a gap in the collection but its not exactly complicated to solve. The way this puzzle was made was by using two centres and a core of a QiYi Sail. As these parts already spin like a 1x1x3 should all I had to do was make these parts into cubies by adding some apoxie sculpt and sanding them smooth. This puzzle was made in an afternoon and stickered the following morning while I was also building my 'Mefferts bandage cube'.

^{Rubik’s Build It Solve It is very similar to the traditional Rubik’s cube, but with a slight twist. With this cube you get all of the tools and bit’s and pieces along with the instructions. This is all you will need in order you you to build a Rubik’s Cube of your own. Once you have fitted the cube together, an instruction booklet has been included, and it is 10-pages in length. Finally, you will learn after all these years the process of solving Rubik’s Cube. You will be shown everything from identifying the parts of the cube along with solving basic puzzles. When you buy this toy, your children will be shown a slow and steady way of using the cube. They will then progress further with the toy to learn even harder challenges. }

The standard Rubik's cube has sides of about 2.2 in (5.7 cm) per square. Various other sizes have also been produced such as a 1.5 in (3.8 cm) mini cube, a 0.8 in (2 cm) key chain micro cube, and a 3.5 in (9 cm) giant cube. While the standard cube is a 3 × 3 × 3 segmentation other types have also been introduced. Some of the more interesting ones include the 2 × 2 × 2 cube, the 4 × 4 × 4 cube (called Rubik's Revenge) and the 5 × 5 × 5 cube. The shape has also been varied and puzzles in the form of a tetrahedral, a pyramid, and an octahedral are among types that were produced. The Rubik's cube also led to the development of game derivatives like the Rubik's cube puzzle and the Rub it cube eraser.

_{Here, we're looking at the colours that aren't solved. There are 21 different cases for the top layer, but we only need a couple of algorithms to solve them all. The first thing we want to find is headlights. Only 2 of the cases don't have any headlights (one of them is if you skip this step, and the cube is already solved). For the one case without headlights, just perform the algorithm below from any angle. This is a better case because when you do the next step, the cube will be solved already. }

`There are 5 different positions your cube can be in now, one of which could be solved. The rest of them have all four corners solved, so do the required amount of U moves so that every corner is in its right place. 2 of the 4 remaining possibilities have a solved bar (as mentioned above, where all three colours on that side are the same), and the other 2 have no solved bars.`

*If there are no more edges left on the top layer, then they are probably either inserted in the right place but flipped, or inserted in the wrong place. To get an edge out of somewhere it shouldn't be, just insert one of the yellow edges into that slot. This should get the edge out and on the top layer, ready for you to use the above instructions to insert correctly. Rubix Build*