Repeat the process. Turn back to your blue side and repeat the turns on opposite sides. Then, return once more to the red side and turn the opposite sides in opposite directions. And last, return once more to the blue side and turn the opposite sides in opposite directions. When you finish, you should have a staircase-like zig-zag across four sides of your Rubik’s cube.[4]
Keeping white on top, turn the cube so that a different colour face is toward you. Follow the above instructions again. Repeat with the other two faces until the white cross is complete. This step is quite intuitive; you can do it for sure but it does take a little practice. Just move the white edges to their places not messing up the ones already fixed.  
Twist the bottom layer so that one of the white corners is directly under the spot where it's supposed to go on the top layer. Now, do one of the three algorithms according to the orientation of the piece, aka. in which direction the white sticker is facing. If the white corner piece is where it belongs but turned wrong then first you have to pop it out.
Begin with your cube solved. Once again, you want to start off with your Rubik’s cube in its solved position. Making a fish pattern on your Rubik’s cube is simple. The end result will have swapped two edge pieces so that the remaining ones look like a fish with fins. If you hold the cube diagonally it will look like a fish swimming away from you.[7]
If you were around in the 1980’s and did not live under a rock, you had a Rubik’s cube.  It was the 3D combination puzzle that had children and adults mesmerized trying to solve the impossible puzzle.  We would spend hours twisting and turning the cube to figure the solution. The cube was invented by an Hungarian professor of architecture, Erno Rubik, in 1974.  Although it took Erno over one month to solve his very own puzzle, it  became a fad and everyone had one. Consequently, it became the world’s best selling toy ever at that time. Rubiks Build It Solve It Instructions

We add the BrickPi3 to the LEGO assembly.  We used the LEGO EV3 “wings” to support the BrickPi3 and make it level with the BricKuber body.  This is a good step to add 8XAA batteries to the power pack and attach the BrickPi3 power pack to the LEGO assembly.  For programming you can power the BrickPi3 via USB power to the Raspberry Pi, however to move the motors you will need to supply power with the Power Pack.        

Rubik’s Build It, Solve It is similar to the conventional Rubik’s block, but with a twist. This block includes each the tools, bits and directions kids need to be able to construct a Rubik’s Cube of the own. After this block was assembled together, there’s an education booklet (it’s’s 10-pages in duration) which will direct you through the procedure for solving the Rubik’s Cube (eventually). Here, you’ll find everything from identifying the areas of the block to solving fundamental puzzles. With this toy, kids will be provided a slow and continuous introduction about the best way best to use the block and progress to harder struggles.
There are 5 different positions your cube can be in now, one of which could be solved. The rest of them have all four corners solved, so do the required amount of U moves so that every corner is in its right place. 2 of the 4 remaining possibilities have a solved bar (as mentioned above, where all three colours on that side are the same), and the other 2 have no solved bars.
The standard Rubik's cube has sides of about 2.2 in (5.7 cm) per square. Various other sizes have also been produced such as a 1.5 in (3.8 cm) mini cube, a 0.8 in (2 cm) key chain micro cube, and a 3.5 in (9 cm) giant cube. While the standard cube is a 3 × 3 × 3 segmentation other types have also been introduced. Some of the more interesting ones include the 2 × 2 × 2 cube, the 4 × 4 × 4 cube (called Rubik's Revenge) and the 5 × 5 × 5 cube. The shape has also been varied and puzzles in the form of a tetrahedral, a pyramid, and an octahedral are among types that were produced. The Rubik's cube also led to the development of game derivatives like the Rubik's cube puzzle and the Rub it cube eraser.
The centre pieces on each face, as you may have noticed from playing around with the cube, can't be moved to another spot, only rotated. So we can use this to our advantage by building around the centres. The best centre to build your first cross around is the white centre, as many guides and resources on the web start with a white face, so if you need to look up some steps and examples elsewhere, your cube will look similar to the one that is being used in other demonstrations.
The standard Rubik's cube has sides of about 2.2 in (5.7 cm) per square. Various other sizes have also been produced such as a 1.5 in (3.8 cm) mini cube, a 0.8 in (2 cm) key chain micro cube, and a 3.5 in (9 cm) giant cube. While the standard cube is a 3 × 3 × 3 segmentation other types have also been introduced. Some of the more interesting ones include the 2 × 2 × 2 cube, the 4 × 4 × 4 cube (called Rubik's Revenge) and the 5 × 5 × 5 cube. The shape has also been varied and puzzles in the form of a tetrahedral, a pyramid, and an octahedral are among types that were produced. The Rubik's cube also led to the development of game derivatives like the Rubik's cube puzzle and the Rub it cube eraser.
When you get round to building the Rubik’s Cube, you will find it is not as hard as it appears.  The instructions are quite easy to follow and it will probably take you about fifteen minutes. When you get round to placing the colored tiles, pay attention to where they are supposed to go. Because once you snap them into place. you will not be able to remove them. Having said that. you can still use the Rubik’s Cube. What you will not be able to do is follow the instruction guide and solve the puzzle.
You can find assembly instructions for the BrickPi3 here. We will need to assemble the case, attach the BrickPi3, the Raspberry Pi, the Raspberry Pi Camera, add an SD Card, and add batteries.  To make the software easier to setup, Raspbian for Robots comes with most of the software you will need already setup.  You will need at least an 8 GB SD Card, and you will want to expand the disk to fit the full size of the SD Card. Rubix Builders
×